Plinth Feet Dimensions: Standard Sizes and Custom Options

A plinth foot looks like a small, simple part, but its dimensions carry a surprising amount of engineering. The diameter sets the load it can bear; the height sets the gap under the cabinet; the adjustment range sets how much uneven floor it can correct; and the base size sets how the load spreads into the floor. Get the dimensions right and the foot disappears into the cabinet's foundation, doing its job invisibly. Get one wrong — a foot too tall, a base too small, a range too short — and the cabinet sits wrong or wobbles, no matter how well everything else was built.

This guide covers plinth feet dimensions: what each measurement means, the standard sizes, and when and how to go custom. Based on 15 years of manufacturing plinth feet for cabinet makers across 40+ countries.

Browse plinth feet in every size

The Dimensions That Matter

What Each Measurement Controls

A plinth foot is defined by a handful of dimensions, each with its own job in the cabinet.

The stem diameter carries the load. The threaded stem is under compression, and its diameter — usually M8, M10, or M12 — sets how much weight it can bear. A larger thread carries more, which is why heavy cabinets and commercial units use M12 where a light cabinet uses M8.

The base diameter spreads the load. The base plate is what touches the floor, and a larger base spreads the cabinet's weight over more floor area. On soft or sheet flooring, a larger base prevents the foot from digging in or marking the surface — and it adds stability against tipping.

The height sets the plinth gap. The overall height of the foot defines the space between the cabinet and the floor — the plinth gap that a kickboard covers. Standard kitchen cabinets use a 100-150mm plinth height, and the foot must match that.

Plinth feet dimensions explained

Standard Sizes

The Sizes That Cover Most Cabinets

Most cabinets are served by a small set of standard sizes, and matching those is cheaper and faster than going custom.

Standard sizes are matched to standard cabinets. A 150mm plinth height with an M10 stem and a 50mm base serves the vast majority of kitchen base cabinets. The standardization is why these parts are economical and immediately available — the volume exists because the sizes are common.

Adjustment range follows the floor. Standard adjustment of 10-20mm handles the minor unevenness of a reasonably installed floor. Where the floor is more uneven — older buildings, commercial spaces — a wider range of 20-50mm gives the foot enough travel to correct it without resorting to shims.

Load drives the stem and base. As the cabinet gets heavier — a tall pantry, a loaded commercial unit — both the stem diameter and the base diameter step up, because the load must be both carried (stem) and spread (base). Heavier cabinet, larger foot.

Standard plinth feet sizes

Reading a Dimension Specification

The Numbers on the Data Sheet

A plinth foot's specification sheet lists its dimensions in a standard order, and reading it correctly is the difference between ordering the right part and the wrong one.

The stem length and total height are different things. The stem length is the threaded portion; the total height is the installed foot height including the base. Confusing the two is the most common ordering error — a foot ordered by stem length when the total height was needed arrives too tall or too short.

The adjustment range is additional height. A foot listed as 100-120mm has a minimum height of 100mm and can extend 20mm to 120mm. The cabinet must be designed for the minimum, with the range as reserve for leveling — not the reverse.

Load rating is per foot, not per cabinet. A rating of 100kg means each foot carries up to 100kg. A four-foot cabinet is therefore rated for up to 400kg — but only if the load is evenly distributed, which in practice it never perfectly is. Size each foot with margin.

Dimension specifications for every foot

Matching Dimensions to the Cabinet

The Fit That Makes the Foot Work

The height must match the plinth. The foot's total height, plus the cabinet's base, must equal the intended plinth gap. If the design calls for a 150mm kickboard and the feet are 100mm, the cabinet sits too low and the kickboard will not fit. Height is the dimension that most often goes wrong.

The stem must match the weight. An M8 stem is adequate for a light bedroom cabinet; a loaded kitchen base or a commercial unit needs M10 or M12. Under-sizing the stem is invisible at purchase and expensive at failure — the foot buckles or strips, and the cabinet drops.

The base must match the floor. On a soft vinyl or timber floor, a small base concentrates the load and marks or digs into the surface. A larger base spreads it, protecting the floor and adding stability. Match the base diameter to the floor material, not just to the load.

Match feet to your cabinet

Custom Options

When Standard Sizes Do Not Fit

When a cabinet's design falls outside standard sizes — an unusual plinth height, a non-standard load, a specific base diameter — a custom plinth foot is the answer.

Custom is a dimensions and volume decision. A custom foot's economics depend on quantity — tooling for a one-off is expensive, while a production run amortizes it. Custom is worthwhile for a product line with non-standard dimensions, and rarely for a single cabinet.

Specify the dimension you actually need changed. The most efficient custom order changes one dimension and keeps the rest standard — a longer stem on a standard base, a larger base on a standard stem. Changing everything at once is a new part, with new tooling and a longer lead time.

Confirm the tolerance and the sample. A custom foot should be specified with tolerances and confirmed with a pre-production sample, so the delivered part matches the design before a batch is made. The sample is cheap insurance against a dimension that was specified wrong.

Discuss custom plinth feet dimensions

Common Mistakes

The Errors That Order the Wrong Foot

The unifying lesson: plinth feet dimensions are not arbitrary numbers to glance at — each one controls a real aspect of fit, load, and leveling, and getting one wrong shows up later as a cabinet that sits wrong or fails. Read the specification precisely, match each dimension to the cabinet's requirement, and the foot disappears into the foundation and does its job.

Conclusion

A plinth foot's dimensions are its engineering — the stem diameter that carries the load, the base that spreads it, the height that sets the plinth gap, and the range that levels the floor. Standard sizes serve most cabinets cheaply and immediately; custom dimensions cover the designs that fall outside. Match each dimension to the cabinet's weight, floor, plinth height, and unevenness, and the foot becomes the invisible foundation the cabinet was designed to sit on.

Key takeaways:

At Shaxi Hardware, every plinth foot ships with documented thread, stem length, base diameter, total height, adjustment range, and load rating, matched to the cabinet and the floor. Our ISO 9001 certified facility manufactures standard and custom sizes, and our technical team helps specify the right dimensions for any cabinet. Because a foot that fits right is the foundation that never gets noticed.

Request plinth feet dimension specifications

Additional Resources

• [Link to: /collections/adjustable-connecting-leveller – Plinth Feet & Cabinet Levellers]
• [Link to: /collections/connecting-fittings – Fasteners & Fixings]
• [Link to: /collections/stainless-steel-screw – Corrosion-Resistant Hardware]
• [Link to: /collections/shelf-support – Shelf Supports for Cabinets]
• [Link to: /pages/about-us – ISO 9001 Manufacturing & Testing]
• [Link to: /pages/contact – Selection Consultation]

About Shaxi Hardware

With over 15 years of experience manufacturing furniture hardware, Shaxi Hardware serves brands and manufacturers across 40+ countries. Our ISO 9001 certified production facility manufactures plinth feet in standard and custom dimensions, with documented thread, stem length, base diameter, total height, adjustment range, and load rating. Batch quality control is conducted on every production run, and our technical team specifies dimensions for cabinet weight, floor, and plinth height. Third-party verification by SGS, TÜV, Intertek, or Bureau Veritas is welcomed.

Learn more about Shaxi Hardware